Updated on November 19, 2026

If your external SSD is slow over USB-C, time a copy with your usual setup. Repeat it with the drive plugged directly into your computer using its supplied data cable. If the second copy is faster, put the original cable and the dock back one at a time. That tells you which part to check before you spend money.
Find the bottleneck with one file
Choose an existing file of roughly 4 GB, such as a video. In Finder or File Explorer, copy it into a fresh folder for each run. Use the same computer, file and copy direction, and time each copy from start to finish. Test writes if copying to the SSD is slow. Test reads if copying from it is slow.
- Time your usual setup. Keep the cable, port and dock you normally use. Write down how long the copy takes.
- Set a direct baseline. Eject the SSD before reconnecting it. Plug it into the computer with the SSD’s supplied data cable, then time the same copy. Use the same computer port if it fits.
- Put each part back separately. Eject the SSD between runs. Test the original cable directly, then test the supplied cable through the same dock socket. If both cables are slow when connected directly, test a second computer port with a known data rating.
Divide the file size in megabytes by the time in seconds to estimate the average speed. Here is a worked example for a 4 GB file (about 4,000 MB). Use your own timings to tell which part makes a difference.
| Connection used | Time for 4 GB | Average speed |
|---|---|---|
| Original cable through the dock | 100 seconds | 40 MB/s |
| Supplied cable directly to the computer | 5 seconds | 800 MB/s |
| Original cable directly to the computer | 100 seconds | 40 MB/s |
| Supplied cable through the dock | 5 seconds | 800 MB/s |
The slowdown follows the original cable in this example. If both cables run quickly when connected directly and slow down through the dock, check the dock’s port rating before trying a replacement.
Check the USB speed the drive is using
Around 40 MB/s is a clue. For instance, a USB 2.0 link reported at 480 Mb/s can carry up to 60 MB/s before overhead. Check the reported link speed as well as your copy time. The USB-IF’s cable labeling guide shows what data rates to look for when comparing cables.
On a Mac, open the System Information report and select your SSD under USB to read its speed entry. A Thunderbolt or USB4 drive may appear under Thunderbolt/USB4. Select the drive itself so you can read its connection details.
On Windows, Microsoft’s USBView shows the USB device tree and connection information it can read. If your device’s speed is unclear or you prefer to use File Explorer alone, the timed copy across the different connections will still show where the speed changes.
What if the connection stays the same and speeds still vary?
| What you see | Test to run next |
|---|---|
| One big file copies quickly and a folder with thousands of files crawls. | Compare one large file with a folder of about the same total size. Opening and recording each small file adds work. |
| Copies from the external SSD are fast and copies to it are slow. | Check the write result with a large file from a fast internal SSD. Use the same port and cable for both directions. |
| A long copy to the SSD starts fast and then stays slow. | Watch when the speed drops and how much you have copied. Compare that pattern with a sustained-write test for your drive’s exact model and capacity. |
| The SSD becomes slow only when another drive is active on the dock. | Repeat the same copy after the other transfer ends. Speed that returns points to the two devices sharing the dock’s connection. |
Some drives have a small area of fast flash that handles the start of a write. Once that area fills, the rest of the copy can take longer. In a Tom’s Hardware sustained-write benchmark, the 1 TB PNY RP60 started above 1,700 MB/s and settled below 400 MB/s after about four minutes. A short copy would have shown only its faster phase.
Frequently asked questions
Can a USB-C cable charge quickly and copy files slowly?
Yes. A cable’s wattage describes charging. Some high-wattage cables still transfer data at USB 2.0 speeds. Check the cable’s data rating as well as the power rating.
Why is my 2,000 MB/s portable SSD closer to 1,000 MB/s?
Check which USB mode your drive needs. The Samsung T9 is rated for up to 2,000 MB/s with USB 3.2 Gen 2×2. If the connection is running at 10 Gb/s, results near 1,000 MB/s are normal. Check the port’s specs to confirm it supports the drive’s mode.
When would a new NVMe enclosure help?
If you built the external SSD yourself and its enclosure sets the speed limit, look for one whose data mode your computer also supports. Our guide to USB-C NVMe enclosures explains the options. Check the port, enclosure and cable before choosing one.
When should I check the SSD’s health?
If a file copy fails, files become unreadable, or the drive repeatedly disconnects, prioritize copying important files to another drive. Then use our guide to checking SSD health to see what health information your enclosure exposes.