Updated on
Compare the TP-Link TL-SX105 and TRENDnet TEG-S750 V2 if you need five 10G Ethernet ports. Choose the QNAP QSW-2104-2T-R2 if two 10G ports and four 2.5G ports suit your setup. All three are listed as unmanaged and fanless. Check how many ports actually run at 10Gb/s and which hardware version you are buying.

Compare these unmanaged 10G switches
| Exact model | Ports and speeds | Cooling | Manufacturer’s maximum power rating | Size |
|---|---|---|---|---|
| TP-Link TL-SX105 | 5 × RJ45; 100M, 1G, 2.5G, 5G and 10G. | Fanless. | 21.4 W. | 226 × 131 × 35 mm. |
| QNAP QSW-2104-2T-R2 | 2 × multi-gig 10G RJ45 plus 4 × 2.5G RJ45. Only two ports reach 10G. | Fanless. | 18 W. | 160 × 110 × 26 mm. |
| TRENDnet TEG-S750 V2 | 5 × RJ45; V2 lists 1G, 2.5G and 10G. Do not infer 5G support. | Fanless. | 22.75 W. | 180 × 145 × 33 mm. |
The table uses manufacturer specifications checked on November 2, 2026. We have not measured power use, heat, transfer speed or noise. Prices and stock depend on where you buy. Check the exact model and hardware version: an older TEG-S750 or a QNAP 2S model may have different specifications.
Count how many 10G devices you need to connect
If only your computer and NAS need 10G, QNAP’s two 10G ports may be enough. Its other four ports run at up to 2.5G. Remember to count any port you need to connect to another switch or router at 10G.
Five 10G ports give you more room for extra computers or another NAS. Check the speeds between 1G and 10G too. TP-Link lists 5G for the TL-SX105. TRENDnet’s cited V2 page lists 1G, 2.5G and 10G.
RJ45 versus SFP+ and combo ports
RJ45 ports use compatible copper Ethernet cables. SFP+ ports need a suitable direct-attach cable, often called a DAC, or a transceiver module. Before choosing SFP+, check which cables or modules the switch supports, how far they can run, their heat and the total cost.
A combo port gives you two connector choices for one connection. Do not count both sockets as separate ports you can use at once unless the manufacturer says so. Model names matter too: QNAP’s 2T and 2S versions use different types of 10G connection.
Check cooling and noise
Fanless means there is no cooling fan making noise. It does not guarantee that the whole setup is silent or stays cool anywhere you put it. Leave room for air to circulate and follow the installation guide, especially with several 10G copper links in use.
The wattages in the table are the manufacturers’ maximum ratings. They are not measurements of what your setup will use. Real power use depends on the ports, link speeds, traffic and power supply. Check that any figure you compare belongs to the same hardware version.
Check your cables, computer and storage
For new copper 10G cable runs up to 100 meters, Cat 6A is a straightforward choice. Cat 6 can work over shorter distances in suitable conditions. Do not assume an old Cat 5e run will handle 10G. Check wall sockets and patch cables as well as the main cable.
A 10G switch cannot make a 1G network card run at 10G. The NAS, disks, computer and network software can also slow a transfer. Ten gigabits per second works out to 1.25 gigabytes per second before network overhead. Real file copies will be slower.
A wireless laptop also depends on its Wi-Fi speed, even when the NAS uses Ethernet. Our wireless-storage guide explains the different connections.
When you need a managed switch
Choose unmanaged if you want a simple switch without settings to configure. If you need VLANs, link aggregation, port monitoring or traffic controls, look for a managed model that supports them. Ethernet ports do not automatically provide PoE power either.
If you need to keep groups of devices separate, read our network-segmentation guide before choosing a basic unmanaged switch.
Common questions
Will a 10G switch make my internet connection faster?
Only if the part you replace was slowing the connection down. Your internet plan, router and computer still set limits.
Does a six-port switch have six 10G ports?
No. The QNAP here has two 10G ports and four 2.5G ports. Check the speed of each group of ports.
Which compared switches have no fan?
All three are listed as fanless. We have not independently measured their noise.
Can I combine ports for a faster transfer?
Do not assume so. An unmanaged switch may not support setting up link aggregation. Even where aggregation is supported, it does not necessarily double the speed of one file transfer.